Archives for 


AVR ATMega8 Schematic Circuit with Eagle Software



ATMega8 Schematic Circuit (Minimum system) is a support circuit for the microcontroller.

Without this support circuit, the microcontroller will not be able to work.

Minimum system for microcontrollers consist of several components. The components are : crystal, capacitors, and the reset circuit (consisting of resistors and capacitors).

And the crystal must be combined by two capacitors. The capacity of this capacitor should be in accordance with the AVR ATMega8 datasheet.

RESET pin on AVR ATMega8 must be pull up with a 4K7 ohm resistor and stabilized with ‘100nF capacitors’.

You have to make the pin as a downloader port. pin of the downloader port must meet a standard sequence. The pin sequence is: MOSI, MISO, SCK, RESET, GROUND.

This AVR ATMega8 schematic is made with the EAGLE software.

ATMega8535 Schematic Diagram



AVR ATMega8535 is a very popular microcontroller.

In the recent years, ATMega8535 has been displaced by the other microcontroller with a more complete feature like ATMega32, ATMega16 or ATMega128. Even, when Arduino offers ease (in the used and programming), the conventional Microcontroller becoming obsolete.

However, some users are still loyal to use the conventional microcontroller. And if you want to learn about the basics of the microcontroller, then you have to learn from the conventional microcontroller. You have to create an electronic circuit by yourself. And you have to find out all about the components used. After you finish creating the electronic circuits, then you will understand how the microcontroller’s minimum system so that it able works. And you will understand how a microcontroller work,  before you start programming it.

Like other microcontroller, we need some electronic components so that it able to work.

Crystal,some resistor and capacitor for the clock and the reset button. And don’t forget to provide the supply (VCC and GND) on the microcontroller board. You can make the ATMega8535 schematic diagram with the EAGLE software like the exsample above.

AVR ATMega128 Schematic Circuit Adapter DIY



ATmega128 is one of the AVR microcontroller. Large memory (128KBytes) can be used to make a big project.

For example, if you create a storage system using the MMC and use BASCOM AVR as the programming language, then you have to load a very large libraries into the memory of the microcontroller. And this can not be done if you are using a microcontroller with a small memory such as ATMega16 or ATMega8535. Therefore, you can try using AVR ATmega128 to complete your major project.

However, you would have difficulty in assembling and soldering components on this ATmega128 microcontroller. This is because ATmega128 an SMD component. And you must be able to make a double layer PCB if you want to use a ATmega128 microcontrollers and use part of DIP components (such as IC MAX232 or another).

If you want to combine the two types of these components, then I have tips for you. Make two single PCB layer and combine with pin headers. The first is an adapter PCB for ATmega128 microcontroller and the second is used for the other DIP components. And then combine it with pin header (male and female pin header). You can see PCB adapter for ATmega128 microcontroller in the picture.

DIY – Do It Yourself project

Hopefully this tutorial ( AVR ATMega128 Schematic Circuit Adapter DIY ) can help you in completing the project.

USBasp AVR Microcontroller Downloader Schematics



This USBasp downloader can be used on the AVR microcontroller families such as ATMega8, ATmega16, ATMega8535, ATmega32, ATmega128 and much more. Based on Atmega8 (or can also be used ATMega88) and some additional components.

USB connector as the interface with a computer and five pins as an interface with a microcontroller. The USBasp’s hardware is very easy to make. Once you finish making the hardware, you should fill the ATMega8’s memory with two firmware program that will be filled in eeprom microcontroller ATmega8.

After that, USBasp downloader has been ready for use. To download the program, you must compile into .hex file using BASCOM AVR or CAVR.

And you can transfer files with the .hex downloader software like avrdude, USBasp, khazama, PonyProg or other programs.

avr microcontroller BOARD schematics downloader

avr microcontroller BOARD schematics downloader